1. The fault is connected to the starting gear of the ignition switch. The starter is idle and cannot engage the flywheel teeth to drive the engine.

　　2、故障原因單向離合器打滑或損壞；撥叉變形、嚙合彈簧折斷或太軟；起動機主開關行程調整不當，以致開關閉合時間過早或起動機固定螺栓松動等。

　　2. Failure causes include slippage or damage of one-way clutch, deformation of fork, breakage of meshing spring or too soft, inappropriate adjustment of main switch stroke of starter, premature closing time of switch or loosening of fixed bolt of starter, etc.

　　3、故障排除

　　3. Troubleshooting

　　①起動機空轉時轉速很高，可聽到高速轉動的“嗡—”聲，但發動機不轉。一般為單向離合器打滑，應檢查單向離合器的鎖止轉矩，并予以檢修、調整。

　　When the starter idles, the speed is very high, and the "buzz" sound of high-speed rotation can be heard, but the engine does not turn. Generally, the one-way clutch slips. The locking torque of the one-way clutch should be checked and repaired and adjusted.

　　②起動時伴有齒輪撞擊聲：應檢查嚙合彈簧是否折斷或過軟；起動機主開關行程調整是否合適；起動機固定螺栓是否松動等。可依據檢查所見具體情況予以修理。

　　(2) Starting with gear impact sound: check whether the meshing spring is broken or too soft; whether the main switch stroke adjustment of starter is appropriate; whether the fixed bolt of starter is loose, etc. It can be repaired according to the specific conditions seen in the inspection.
汽車電動機出現空轉現象的原因！

　　少防眩目前照燈是在近光燈絲上加上了配光屏，使一半的光通量被截止，通過配光鏡得到非對稱性光型，從而充分限制了迎面車輛駕駛人受到照射的光束，又可使行車路線得到良好的照明，提高了夜間會車的安全系數。

　　At present, the light distribution screen is added to the low-light filament to cut off half of the light flux. The asymmetric light pattern is obtained through the light distribution mirror, which fully limits the light beam to the driver of the vehicle in front of him, and makes the driving route get good illumination, and improves the safety factor of meeting at night.

　　防眩目前照燈的特征是近光燈絲有一塊配光屏，而且配光屏與燈絲正投影水平方向成15“偏角，擋住下半部光源。在配光鏡玻璃表面左右兩邊有不對稱的花紋，花紋的正方向右下方有偏角巧“的直線，以使汽車在道路右側行駛時，上方是一個明顯的暗區，而在下方及右上15“內是一個亮區，從而達到汽車夜間交會時，避免燈光眩目的效果。

　　At present, the anti-glare feature of the headlamp is that the low-light filament has a light distribution screen, and the light distribution screen and the filament projection are at a horizontal angle of 15 "to block the lower half of the light source. There are asymmetrical patterns on the left and right sides of the glass surface of the light matching mirror, and the right and lower sides of the patterns have a line with a deflection angle, so that when the car is driving on the right side of the road, the upper side is a clear dark area, while the lower and upper right 15 "is a bright area, so as to achieve the effect of avoiding the glare of the lights when the car intersects at night.